How to String a DeWalt String Trimmer
To string a DeWalt string trimmer, remove the spool, thread the correct line through its holes, wind it in the marked direction, and reinstall it without crossing the line. Disconnect the battery before working on the head.
On this page (11 sections)
- What do you need before stringing a DeWalt trimmer?
- How do you remove the DeWalt spool?
- How do you measure and cut replacement line?
- How do you wind the line on a DeWalt spool?
- What replacement head can simplify line changes?
- How do you reinstall the spool and cap?
- What if you want a trimmer that also edges?
- How do you fix DeWalt line feeding problems?
- How should you care for the spool after restringing?
- What should you check before trimming again?
- What is the easiest way to string a DeWalt string trimmer?
To string a DeWalt string trimmer, remove the battery, take off the spool, load the correct line in the arrow direction, and reinstall the spool with both line ends passing through the eyelets. Keep the wraps even so the line can leave the head without binding.
This process covers manual line replacement on common DeWalt bump-feed heads. Your exact model may use a different spool, cap, or release method, so check its manual and the markings on the head before cutting line.
What do you need before stringing a DeWalt trimmer?
You need the correct replacement line, eye protection, gloves, and a clean work area. Remove the battery first, even if the trimmer appears switched off.
Check the spool for its line diameter and winding arrow. If the line size is missing, use the trimmer manual or the original spool as your guide.
Do not force thicker line into a head made for a smaller diameter.
If you're still choosing a tool, our string trimmer weed eater guide explains the main head, shaft, power, and edging differences.
Is manual line winding or a replacement spool easier?
A preloaded spool is usually faster, while manual winding gives you more control over the line length and type. Manual winding makes sense when the spool is usable and you already have compatible line.
The DEWALT N508388 is a preloaded replacement spool and string for the DCST920P1, DCST970BR, DCST970X1, and DCST991M1 cordless string trimmers.

A preloaded DEWALT N508388 spool and string that suits listed compatible trimmer models when you want to skip manual winding.
See it on AmazonChoose this route only after matching the model number. It includes 1 replacement part, with a durable impact-resistant plastic spool and preloaded trimmer line.
How do you remove the DeWalt spool?
Turn the trimmer off, remove the battery, and press the spool-release tabs before lifting off the cap and spool. Clear grass and dirt from the head so the tabs and eyelets can move freely.
Hold the head steady with one hand. Press the tabs on opposite sides of the spool cap, then pull the cap and spool away from the trimmer.
If the cap does not release, do not pry against the plastic with a knife or screwdriver. Look for packed debris, then consult the model manual for the correct release method.
Set the old spool aside and inspect the head. Look for damaged eyelets, cracks, worn tabs, or a spring that has shifted from its position.
How do you measure and cut replacement line?
Cut enough line for the spool's marked capacity, not an oversized length that fills the cavity. The correct diameter and length vary by DeWalt model and spool.
Straighten the line before measuring. A kink can make the first wraps uneven and cause the line to catch when the head turns.
For a broad comparison of compatible options, see our guide to the best DeWalt string trimmer line. If your head uses 0.080 in line, the best DeWalt .080 string trimmer line guide focuses on that size.
Do not guess from the trimmer's cutting width. Cutting width describes the area swept by the head, not the line diameter the spool accepts.
How do you wind the line on a DeWalt spool?
Thread the line into the anchor hole, then wind it in the arrow direction with tight, parallel wraps. Keep the line in one layer and leave the ends in the spool's holding notches when finished.
- Find the small anchor hole or slot inside the spool.
- Insert the line far enough to hold it securely.
- Follow the arrow molded into the spool.
- Wind the line in even rows without crossing it.
- Stop at the fill line or leave the clearance shown on the spool.
- Secure the line in the holding notches.
Some spools use one continuous length of line. Others use separate channels or a divided center.
Follow the physical markings on your spool rather than copying a winding method from another DeWalt model.
The most common winding error is reversing the direction. A reversed spool can look tidy but fail to release line when the bump head contacts the ground.
What replacement head can simplify line changes?
A fixed-line head can reduce the need to open and rewind a spool. See options in our guide to replacement string trimmer heads.
The Weed Warrior EZ Lock Universal Fit String Trimmer Replacement Head uses pre-cut line strips and an EZ Lock design.

A black EZ Lock replacement head with a 4-line design for 0.080 to 0.095 in pre-cut line strips.
See it on AmazonThe head includes a universal fit hardware kit and is intended for trimming, edging, and weed eating tasks. Its 4-line design suits readers who prefer loading short strips instead of winding a continuous length.
The product data names DeWalt 20V, 40V, and 60V among its cordless fit categories, but model fit still needs to be checked before installation. Remove the old head and use the included adapter or hardware if the head requires it.
This option changes the loading method. It is not the same as replacing line on the original DeWalt spool, so confirm that the head's mounting method suits your trimmer.
How do you reinstall the spool and cap?
Guide both line ends through the eyelets, seat the spool on the spring, and press the cap down until the tabs lock. Pull each line end gently to confirm it moves through the eyelets.
Keep the spool flat while fitting it. If the line slips out of the holding notches too early, rewind or secure it again before placing the cap.
After the cap clicks into place, turn the spool by hand if the design allows it. The line should move smoothly and stay inside the eyelets.
Trim uneven ends only after the spool is installed. Use the trimmer's guard blade to set the working length during operation, and never pull out more line than the guard is designed to cut.
What if you want a trimmer that also edges?
The WORX 20V 12" 2-in-1 Cordless String Trimmer converts from trimming to edging and uses a push-button Command Feed spool system. For more combined-tool options, compare string trimmer and edger combos.
It includes 2 batteries, a charger, a spool, a safety guard, and support wheels.

A 20V 12 in trimmer and edger with push-button line feeding for readers who want to avoid manual spool winding.
See it on AmazonIts 0.065 in line, 12 in cutting diameter, 7,600 rpm no-load speed, and 5.5 lb machine weight describe a different setup from a DeWalt manual-wind head. The head tilts 90 degrees, and rubberized wheels guide edging cuts.
This is a separate tool choice, not a DeWalt spool replacement. Its PowerShare system works with WORX 20V and 40V tools, so it may suit someone building that battery platform.
How do you fix DeWalt line feeding problems?
Remove and reload the spool if the line jams, stays inside the head, or feeds unevenly. Most problems come from incorrect winding, crossed wraps, excess line, or debris around the eyelets.
Check these points in order:
- Confirm the line diameter matches the spool.
- Check that the line follows the molded arrow.
- Separate any crossed or overlapping wraps.
- Leave space below the spool rim.
- Clear grass from the eyelets and cap.
- Make sure the spring and spool sit flat.
- Check that the cap tabs are fully locked.
Do not yank hard on a stuck line. Pulling can damage the eyelet or unwind the spool into a tighter knot.
If the spool is cracked or the cap no longer locks, replace the damaged part. Readers comparing complete tools can also review the best DeWalt battery string trimmer options before choosing a replacement.
How should you care for the spool after restringing?
Keep the trimmer head clean and dry after use. Brush away grass from the cap, eyelets, and guard before storing the tool.
Avoid leaving loose line exposed in direct heat or sunlight for long periods. Store spare line in a dry place and keep it straight enough to avoid permanent kinks.
Use the battery recommended for your specific tool. If you're comparing compatible packs, our guide to the best battery for DeWalt weed eater covers that choice.
A straight shaft and curved shaft can also change how the tool feels during trimming. See the straight shaft vs curved shaft trimmer comparison if you're deciding between tool styles.
What should you check before trimming again?
Test the spool by hand before installing the battery, then run the trimmer briefly in an open area with eye protection. Confirm that the line feeds evenly and that no part of the head wobbles.
Keep people, pets, and loose objects away from the cutting area. Use the guard supplied for the trimmer and stop immediately if the head vibrates or makes an unusual sound.
For lawn layouts that need a separate edging tool, our guide to an edger attachment for lawn tractor covers a different equipment setup. If you want to compare complete DeWalt options, see the best DeWalt string trimmers guide.
What is the easiest way to string a DeWalt string trimmer?
The easiest method is to match the line size, follow the spool arrow, use even wraps, and check the eyelets before reinstalling the cap. Choose manual winding when the original spool is sound, a preloaded N508388 spool when your model is compatible, or an EZ Lock head when pre-cut strips better fit your routine.
For any DeWalt string trimmer replacement, the model number and spool markings control the final choice. If the line will not feed after a careful reload, inspect the head for worn parts instead of forcing the spool.
Frequently asked questions
What direction do you wind line on a DeWalt trimmer?
Wind the line in the direction shown by the arrow on the DeWalt spool, usually keeping each wrap neat and tight without crossing over earlier wraps. The arrow on your exact head is the final guide because spool designs can differ.
What size line does a DeWalt string trimmer use?
The correct line size depends on the DeWalt trimmer and head. Check the owner's manual or the marking on the spool before cutting line.
A thicker line may not feed correctly if the head is designed for a smaller diameter.
Why won't my DeWalt trimmer line feed?
Line may fail to feed because it was wound in the wrong direction, packed too tightly, crossed over itself, or cut too long. Remove the spool, unwind the line, inspect the holes and eyelets, then reload it with even wraps.
Can you replace a DeWalt trimmer spool instead of restringing it?
Yes, a compatible preloaded spool can replace manual winding. Confirm the exact DeWalt model before ordering, since a spool made for one trimmer may not fit another head or line-feed system.
About this guide: Our look at stringing a DeWalt string trimmer draws on maker specs, materials and what owners report. See how we research.



